mirror of https://github.com/dswd/vpncloud.git
71 lines
2.8 KiB
Plaintext
71 lines
2.8 KiB
Plaintext
# Whether this VPN should be started with the daemon.
|
|
ENABLED=0
|
|
|
|
# The address to listen for data. [default: `0.0.0.0:3210`]
|
|
# Note: Every VPN needs a different listen address.
|
|
LISTEN=''
|
|
|
|
# Address of a peer to connect to. The address should be in the form
|
|
# `addr:port`. If the node is not started, the connection will be retried
|
|
# periodically. This parameter can be repeated to connect to multiple peers.
|
|
# Note: Several entries can be separated by spaces.
|
|
PEERS=''
|
|
|
|
# Peer timeout in seconds. The peers will exchange information periodically
|
|
# and drop peers that are silent for this period of time. [default: `1800`]
|
|
PEER_TIMEOUT=''
|
|
|
|
# Switch table entry timeout in seconds. This parameter is only used in switch
|
|
# mode. Addresses that have not been seen for the given period of time will
|
|
# be forgot. [default: `300`]
|
|
DST_TIMEOUT=''
|
|
|
|
# An optional token that identifies the network and helps to distinguish it
|
|
# from other networks.
|
|
NETWORK_ID=''
|
|
|
|
# An optional shared key to encrypt the VPN data. If this option is not set,
|
|
# the traffic will be sent unencrypted.
|
|
SHARED_KEY=''
|
|
|
|
# The encryption method to use ("aes256", or "chacha20"). Most current CPUs
|
|
# have special support for AES256 so this should be faster. For older
|
|
# computers lacking this support, only CHACHA20 is supported.
|
|
# [default: `chacha20`]
|
|
CRYPTO=''
|
|
|
|
# Name of the virtual device. Any `%d` will be filled with a free number.
|
|
# [default: `vpncloud%d`]
|
|
DEVICE=''
|
|
|
|
# Set the type of network. There are two options: **tap** devices process
|
|
# Ethernet frames **tun** devices process IP packets. [default: `tap`]
|
|
TYPE=''
|
|
|
|
# The mode of the VPN. The VPN can like a router, a switch or a hub. A **hub**
|
|
# will send all data always to all peers. A **switch** will learn addresses
|
|
# from incoming data and only send data to all peers when the address is
|
|
# unknown. A **router** will send data according to known subnets of the
|
|
# peers and ignore them otherwise. The **normal** mode is switch for tap
|
|
# devices and router for tun devices. [default: `normal`]
|
|
MODE=''
|
|
|
|
# The local subnets to use. This parameter should be in the form
|
|
# `address/prefixlen` where address is an IPv4 address, an IPv6 address, or a
|
|
# MAC address. The prefix length is the number of significant front bits that
|
|
# distinguish the subnet from other subnets. Example: `10.1.1.0/24`.
|
|
# Note: Several entries can be separated by spaces.
|
|
SUBNETS=''
|
|
|
|
# A command to setup the network interface. The command will be run (as
|
|
# parameter to `sh -c`) when the device has been created to configure it.
|
|
# The name of the allocated device will be available via the environment
|
|
# variable `IFNAME`.
|
|
IFUP=''
|
|
|
|
# A command to bring down the network interface. The command will be run (as
|
|
# parameter to `sh -c`) to remove any configuration from the device.
|
|
# The name of the allocated device will be available via the environment
|
|
# variable `IFNAME`.
|
|
IFDOWN=''
|