mirror of https://github.com/dswd/vpncloud.git
89 lines
3.6 KiB
Plaintext
89 lines
3.6 KiB
Plaintext
# This configuration file uses the YAML format.
|
|
|
|
# This configuration can be enabled/disabled and controlled by adding the
|
|
# network to `/etc/default/vpncloud` and starting/stopping it via
|
|
# `/etc/init.d/vpncloud start/stop` on non-systemd systems and via
|
|
# `systemctl enable/disable vpncloud@NAME` and
|
|
# `service vpncloud@NAME start/stop` on systemd systems.
|
|
|
|
|
|
# The port number on which to listen for data.
|
|
# Note: Every VPN needs a different port number.
|
|
#port: 3210
|
|
|
|
# Address of a peer to connect to. The address should be in the form
|
|
# `addr:port`. If the node is not started, the connection will be retried
|
|
# periodically. This parameter can be repeated to connect to multiple peers.
|
|
# Note: Several entries can be separated by spaces.
|
|
#peers:
|
|
# - node2.example.com:3210
|
|
# - node3.example.com:3210
|
|
|
|
# Peer timeout in seconds. The peers will exchange information periodically
|
|
# and drop peers that are silent for this period of time.
|
|
#peer_timeout: 600
|
|
|
|
# Switch table entry timeout in seconds. This parameter is only used in switch
|
|
# mode. Addresses that have not been seen for the given period of time will
|
|
# be forgot.
|
|
#switch_timeout: 300
|
|
|
|
# An optional token that identifies the network and helps to distinguish it
|
|
# from other networks.
|
|
#magic: "76706e01"
|
|
|
|
# An optional shared key to encrypt the VPN data. If this option is not set,
|
|
# the traffic will be sent unencrypted.
|
|
#shared_key: ""
|
|
|
|
# The encryption method to use ("aes256", or "chacha20"). Most current CPUs
|
|
# have special support for AES256 so this should be faster. For older
|
|
# computers lacking this support, only CHACHA20 is supported.
|
|
#crypto: chacha20
|
|
|
|
# Name of the virtual device. Any `%d` will be filled with a free number.
|
|
#device_name: "vpncloud%d"
|
|
|
|
# Set the type of network. There are two options: **tap** devices process
|
|
# Ethernet frames **tun** devices process IP packets. [default: `tap`]
|
|
#device_type: tap
|
|
|
|
# The mode of the VPN. The VPN can like a router, a switch or a hub. A **hub**
|
|
# will send all data always to all peers. A **switch** will learn addresses
|
|
# from incoming data and only send data to all peers when the address is
|
|
# unknown. A **router** will send data according to known subnets of the
|
|
# peers and ignore them otherwise. The **normal** mode is switch for tap
|
|
# devices and router for tun devices. [default: `normal`]
|
|
#mode: normal
|
|
|
|
# The local subnets to use. This parameter should be in the form
|
|
# `address/prefixlen` where address is an IPv4 address, an IPv6 address, or a
|
|
# MAC address. The prefix length is the number of significant front bits that
|
|
# distinguish the subnet from other subnets. Example: `10.1.1.0/24`.
|
|
# Note: Several entries can be separated by spaces.
|
|
#subnets:
|
|
# - 10.1.1.0/24
|
|
|
|
# A command to setup the network interface. The command will be run (as
|
|
# parameter to `sh -c`) when the device has been created to configure it.
|
|
# The name of the allocated device will be available via the environment
|
|
# variable `IFNAME`.
|
|
#ifup: ""
|
|
|
|
# A command to bring down the network interface. The command will be run (as
|
|
# parameter to `sh -c`) to remove any configuration from the device.
|
|
# The name of the allocated device will be available via the environment
|
|
# variable `IFNAME`.
|
|
#ifdown: ""
|
|
|
|
# Store the process id in this file when running in the background. If set,
|
|
# the given file will be created containing the process id of the new
|
|
# background process. This option is only used when running in background.
|
|
#pid_file: ""
|
|
|
|
# Change the user and/or group of the process once all the setup has been
|
|
# done and before spawning the background process. This option is only used
|
|
# when running in background.
|
|
#user: ""
|
|
#group: ""
|