vpncloud/vpncloud.adoc

vpncloud(1)
===========

== Name
vpncloud - Peer-to-peer VPN


== SYNOPSIS

*vpncloud [options] [--config <file>] [-t <type>] [-d <name>] [-l <addr>] [-c <addr>...]*


== OPTIONS

*--config <file>*::
  Read configuration options from the specified file. Please see the section
  *CONFIG FILES* for documentation on the file format.
  If the same option is defined in the config file and as a parameter, the
  parameter overrides the config file.

*-t <type>*, *--type <type>*::
  Set the type of network. There are two options: *tap* devices process
  Ethernet frames *tun* devices process IP packets. [default: *tap*]

*-d <name>*, *--device <name>*::
  Name of the virtual device. Any *%d* will be filled with a free number.
  [default: *vpncloud%d*]

*--device-path <path>*::
  The path of the base device inode, e.g. /dev/net/run.

*-m <mode>*, *--mode <mode>*::
  The mode of the VPN. The VPN can like a router, a switch or a hub. A *hub*
  will send all data always to all peers. A *switch* will learn addresses
  from incoming data and only send data to all peers when the address is
  unknown. A *router* will send data according to known subnets of the
  peers and ignore them otherwise. The *normal* mode is switch for tap
  devices and router for tun devices. [default: *normal*]

*-l <addr>*, *--listen <addr>*::
  The address on which to listen for data. This can be simply a port number
  or a full address in form IP:PORT. If the IP is specified as \'\*' or only
  a port number is given, then the socket will listen on all IPs (v4 and v6),
  otherwise the socket will only listen on the given IP. [default: **3210**]

*-c <addr>*, *--connect <addr>*::
  Address of a peer to connect to. The address should be in the form
  *addr:port*. If the node is not started, the connection will be retried
  periodically. This parameter can be repeated to connect to multiple peers.

*-s <subnet>*, *--subnet <subnet>*::
  The local subnets to use. This parameter should be in the form
  *address/prefixlen* where address is an IPv4 address, an IPv6 address, or a
  MAC address. The prefix length is the number of significant front bits that
  distinguish the subnet from other subnets. Example: *10.1.1.0/24*.

*--shared-key <key>*::
  An optional shared key to encrypt the VPN data. If this option is not set,
  the traffic will be sent unencrypted.

*--crypto <method>*::
  The encryption method to use ("aes128", "aes256", or "chacha20"). Most 
  current CPUs have special support for AES256 so this should be faster. For 
  older computers lacking this support, CHACHA20 is the fastest option.
  [default: *chacha20*]

*--magic <id>*::
  Override the 4-byte magic header of each packet. This header identifies the
  network and helps to distinguish it from other networks and other
  applications. The id can either be a 4 byte / 8 character hexadecimal
  string or an arbitrary string prefixed with "hash:" which will then be
  hashed into 4 bytes.

*--peer-timeout <secs>*::
  Peer timeout in seconds. The peers will exchange information periodically
  and drop peers that are silent for this period of time. [default: **600**]

*--keepalive <secs>*::
  Interval of peer exchange messages in seconds. The peers will exchange
  information periodically to keep connections alive. This setting overrides
  how often this will happen. [default: *peer-timeout/2-60*]

*--dst-timeout <secs>*::
  Switch table entry timeout in seconds. This parameter is only used in switch
  mode. Addresses that have not been seen for the given period of time  will
  be forgotten. [default: **300**]

*--beacon-store <path|command>*::
  Periodically store beacons containing the address of this node in the given
  file or via the given command. If the parameter value starts with a pipe
  character (*|*), the rest of the value is interpreted as a shell command.
  Otherwise the value is interpreted as a file to write the beacon to.
  If this parameter is not given, beacon storage is disabled.
  Please see the section *BEACONS* for more information.

*--beacon-load <path|command>*::
  Periodically load beacons containing the addresses of other nodes from the
  given file or via the given command. If the parameter value starts with a
  pipe character (*|*), the rest of the value is interpreted as a shell
  command. Otherwise the value is interpreted as a file to read the beacon
  from.
  If this parameter is not given, beacon loading is disabled.
  Please see the section *BEACONS* for more information.

*--beacon-interval <secs>*::
  Beacon storage/loading interval in seconds. If configured to do so via
  *--beacon-store* and *--beacon-load*, the node will periodically store its
  beacon and load beacons of other nodes. This parameter defines the interval
  in seconds. [default: **3600**]

*--ifup <command>*::
  A command to setup the network interface. The command will be run (as
  parameter to *sh -c*) when the device has been created to configure it.
  The name of the allocated device will be available via the environment
  variable *IFNAME*.
  Please note that this command is executed with the full permissions of the
  caller.

*--ifdown <command>*::
  A command to bring down the network interface. The command will be run (as
  parameter to *sh -c*) to remove any configuration from the device.
  The name of the allocated device will be available via the environment
  variable *IFNAME*.
  Please note that this command is executed with the (limited) permissions of
  the user and group given as *--user* and *--group*.

*--pid-file <file>*::
  Store the process id in this file when running in the background. If set,
  the given file will be created containing the process id of the new
  background process. This option is only used when running in background.

*--user <user>*::
*--group <group>*::
  Change the user and/or group of the process once all the setup has been
  done.

*--log-file <file>*::
  If set, print logs also to the given file. The file will be created and
  truncated if is exists.

*--stats-file <file>*::
  If set, periodically write statistics on peers and current traffic to the
  given file. The file will be periodically overwritten with new data.

*--statsd-server <server>*::
  If set, periodically send statistics on current traffic and some important
  events to the given statsd server (host:port).

*--statsd-prefix <prefix>*::
  Sets the prefix to use for all statsd entries. [default: **vpncloud**]

*--daemon*::
  Spawn a background process instead of running the process in the foreground.
  If this flag is set, the process will first carry out all the
  initialization, then drop permissions if *--user* or *--group* is used and
  then spawn a background process and write its process id to a file if
  *--pid-file* is set. Then, the main process will exit and the background
  process continues to provide the VPN. At the time, when the main process
  exits, the interface exists and is properly configured to be used.

*--no-port-forwarding*::
  Disable automatic port forward. If this option is not set, VpnCloud tries to
  detect a NAT router and automatically add a port forwarding to it.

*-v*, *--verbose*::
  Print debug information, including information for data being received and
  sent.

*-q*, *--quiet*::
  Only print errors and warnings.

*-h*, *--help*::
  Display the help.


== DESCRIPTION

*VpnCloud* is a simple VPN over UDP. It creates a virtual network interface on
the host and forwards all received data via UDP to the destination. It can work
in 3 different modes:

*Switch mode*:: In this mode, the VPN will dynamically learn addresses
as they are used as source addresses and use them to forward data to its
destination. Addresses that have not been seen for some time
(option *switch_timeout*) will be forgotten. Data for unknown addresses will be
broadcast to all peers. This mode is the default mode for TAP devices that
process Ethernet frames but it can also be used with TUN devices and IP
packets.
*Hub mode*:: In this mode, all data will always be broadcast to all peers.
This mode uses lots of bandwidth and should only be used in special cases.
*Router mode*:: In this mode, data will be forwarded based on preconfigured
address ranges ("subnets"). Data for unknown nodes will be silently ignored.
This mode is the default mode for TUN devices that work with IP packets but
it can also be used with TAP devices and Ethernet frames.

All connected VpnCloud nodes will form a peer-to-peer network and cross-connect
automatically until the network is fully connected. The nodes will periodically
exchange information with the other nodes to signal that they are still active
and to allow the automatic cross-connect behavior. There are some important
things to note:

. To avoid that different networks that reuse each others addresses merge due
to the cross-connect behavior, the *magic* option can be used and set
to any unique string to identify the network. The *magic* must be the
same on all nodes of the same VPN network.
. The cross-connect behavior can be able to connect nodes that are behind
firewalls or NATs as it can function as hole-punching.
. The management traffic will increase with the peer number quadratically.
It should still be reasonably small for high node numbers (below 10 KiB/s
for 10.000 nodes). A longer *peer_timeout* can be used to reduce the traffic
further. For high node numbers, router mode should be used as it never
broadcasts data.

VpnCloud does not implement any loop-avoidance. Since data received on the UDP
socket will only be sent to the local network interface and vice versa, VpnCloud
cannot produce loops on its own. On the TAP device, however STP data can be
transported to avoid loops caused by other network components.

For TAP devices, IEEE 802.1q frames (VLAN tagged) are detected and forwarded
based on separate MAC tables. Any nested tags (Q-in-Q) will be ignored.

== EXAMPLES

=== Switched TAP scenario

In the example scenario, a simple layer 2 network tunnel is established. Most
likely those commands need to be run as *root* using *sudo*.

First, VpnCloud need to be started on both nodes (the address after *-c* is the
address of the remote node and the the *X* in the interface address must be
unique among all nodes, e.g. 0, 1, 2, ...):

----
vpncloud -c REMOTE_HOST:PORT --ifup 'ifconfig $IFNAME 10.0.0.X/24 mtu 1400 up'
----

Afterwards, the interface can be used to communicate.

=== Routed TUN example

In this example, 2 nodes and their subnets should communicate using IP.
First, VpnCloud need to be started on both nodes:

----
vpncloud -t tun -c REMOTE_HOST:PORT --subnet 10.0.X.0/24 --ifup 'ifconfig $IFNAME 10.0.X.1/16 mtu 1400 up'
----

It is important to configure the interface in a way that all addresses on the
VPN can be reached directly. E.g. if subnets 10.0.1.0/24, 10.0.2.0/24 and so on
are used, the interface needs to be configured as 10.0.1.1/16.
For TUN devices, this means that the prefix length of the subnets
(/24 in this example) must be different than the prefix length that the
interface is configured with (/16 in this example).

=== Important notes

. VpnCloud can be used to connect two separate networks. TAP networks can be
bridged using *brctl* and TUN networks must be routed. It is very important
to be careful when setting up such a scenario in order to avoid network loops,
security issues, DHCP issues and many more problems.
. TAP devices will forward DHCP data. If done intentionally, this can be used
to assign unique addresses to all participants. If this happens accidentally,
it can conflict with DHCP servers of the local network and can have severe
side effects.
. VpnCloud is not designed for high security use cases. Although the used crypto
primitives are expected to be very secure, their application has not been
reviewed.
The shared key is hashed using _PBKDF2_HMAC_SHA256_ to derive a key,
which is used to encrypt the payload of messages using _ChaCha20Poly1305_,
_AES128-GCM_, or _AES256-GCM_. The encryption includes an authentication that
also protects the header.
This method does only protect against attacks on single messages but not
against attacks that manipulate the message series itself (i.e. suppress
messages, reorder them, or duplicate them).

== CONFIG FILES

The config file is a YAML file that contains configuration values. All entries
are optional and override the defaults. Please see the section *OPTIONS* for
detailed descriptions of the options.

*device_type*:: Set the type of network. Same as *--type*
*device_name*:: Name of the virtual device. Same as *--device*
*device_path*:: Set the path of the base device. Same as *--device-path*
*ifup*:: A command to setup the network interface. Same as *--ifup*
*ifdown*:: A command to bring down the network interface. Same as *--ifdown*
*crypto*:: The encryption method to use. Same as *--crypto*
*shared_key*:: The shared key to encrypt all traffic. Same as *--shared-key*
*magic*:: Override the 4-byte magic header of each packet. Same as *--magic*
*port*:: A port number to listen on. This option is DEPRECATED.
*listen*:: The address on which to listen for data. Same as *--listen*
*peers*:: A list of addresses to connect to. See *--connect*
*peer_timeout*:: Peer timeout in seconds. Same as**--peer-timeout**
*beacon_store*:: Path or command to store beacons. Same as *--beacon-store*
*beacon_load*:: Path or command to load beacons. Same as *--beacon-load*
*beacon_interval*:: Interval for loading and storing beacons in seconds. Same as *--beacon-interval*
*mode*:: The mode of the VPN. Same as *--mode*
*switch_timeout*:: Switch table entry timeout in seconds. Same as *--dst-timeout*
*subnets*:: A list of local subnets to use. See *--subnet*
*port_forwarding*:: Whether to activate port forwardig. See *--no-port-forwarding*
*user*:: The name of a user to run the background process under. Same as *--user*
*group*:: The name of a group to run the background process under. Same as *--group*
*pid_file*:: The path of the pid file to create. Same as *--pid-file*
*stats_file*:: The path of the statistics file. Same as *--stats-file*
*statsd_server*:: Server to report statistics to. Same as *--statsd-server*
*statsd_prefix*:: Prefix to use when reporting to statsd. Same as *--statsd-prefix*

=== Example

 device_type: tun
 device_name: vpncloud%d
 ifup: ifconfig $IFNAME 10.0.1.1/16 mtu 1400 up
 crypto: aes256
 shared_key: mysecret
 listen: 3210
 peers:
   - remote.machine.foo:3210
   - remote.machine.bar:3210
 peer_timeout: 600
 mode: normal
 subnets:
   - 10.0.1.0/24
 port_forwarding: true
 user: nobody
 group: nogroup
 pid_file: /run/vpncloud.pid

== BEACONS

Beacons are short character sequences that contain a timestamp and a list of
addresses. They can be published and retrieved by other nodes to find peers
without the need for static addresses.

The beacons are short (less than 100 characters), encrypted and encoded with
printable characters to allow publishing them in various places on the
internet, e.g.:

* On shared drives or synchronized folders (e.g. on Dropbox)
* Via a dedicated database
* Via a general purpose message board of message service (e.g. Twitter)

The beacons are very robust. They only consist of alphanumeric characters
and can be interleaved with non-alphanumeric characters (e.g. whitespace).
Also the beacons contain a prefix and suffix that depends on the configured
network magic and secret key (if set) so that all nodes can find beacons in
a long text.

When beacons are stored or loaded via a command (using the pipe character *|*),
the command is interpreted using the configured shell *sh*. This command has
access to the following environment variables:

*$begin*:: The prefix of the beacon.
*$end*:: The suffix of the beacon.
*$data* (only on store):: The middle part of the beacon. Do not use this
without prefix and suffix!
*$beacon* (only on store):: The full beacon consisting of prefix, data and
suffix.
The commands are called in separate threads, so even longer running commands
will not block the node.


== STATSD SUPPORT

When a statsd server is configured (either via **--statsd-server** or the 
config option **statsd_server**), VpnCloud sends out the following statistics
every minute.

Gauge values:
*peer_count*:: Current number of peers
*table_entries*:: Number of routing table / switch table entries

The following statistics consist of two keys: *.bytes* and *.packets* that hold
the values in bytes and packets. All values refer to the traffic during the 
last minute:
*traffic.protocol.inbound*:: Complete incoming traffic with all peers
*traffic.protocol.outbound*:: Complete outgoing traffic with all peers
*traffic.payload.inbound*:: Incoming payload traffic with all peers
*traffic.payload.outbound*:: Outgoing payload traffic with all peers
*invalid_protocol_traffic*:: Invalid incoming protocol traffic
*dropped_payload*:: Outgoing traffic that could not be routed

All keys are prefixed by a common prefix. The prefix defaults to *vpncloud* but
can be changed via **--statsd-prefix** or the config option **statsd_prefix**.


== NETWORK PROTOCOL

The protocol of VpnCloud is kept as simple as possible to allow other
implementations and to maximize the performance.

Every packet sent over UDP contains the following header (in order):

4 bytes *magic*::
This field is used to identify the packet and to sort out packets that do
not belong. The default is *[0x76, 0x70, 0x6e, 0x01]* ("vpn\x01").
This field can be used to identify VpnCloud packets and might be set to
something different to hide the protocol.

1 byte *crypto method*::
This field specifies the method that must be used to decrypt the rest of the
data. The currently supported methods are:

 ** Method *0*, *No encryption*: Rest of the data can be read without
decrypting it.
 ** Method *1*, *ChaCha20*: The header is followed by a 12 byte
_nonce_. The rest of the data is encrypted with the
*libsodium::crypto_aead_chacha20poly1305_ietf* method, using the 8 byte
header as additional data.
 ** Method *2*, *AES256*: The header is followed by a 12 byte _nonce_.
The rest of the data is encrypted with the
*libsodium::crypto_aead_aes256gcm* method, using the 8 byte header
as additional data.

2 *reserved bytes*::
that are currently unused and set to 0

1 byte for the *message type*::
This byte specifies the type of message that follows. Currently the
following message types are supported:

 ** Type 0: Data packet
 ** Type 1: Peer list
 ** Type 2: Initial message
 ** Type 3: Closing message

After this 8 byte header, the rest of the message follows. It is encrypted using
the method specified in the header.

In the decrypted data, the message as specified in the *message type* field
will follow:

*Data packet* (message type 0)::
This packet contains payload. The format of the data depends on the device
type. For TUN devices, this data contains an IP packet. For TAP devices it
contains an Ethernet frame. The data starts right after the header and ends
at the end of the packet.
If it is an Ethernet frame, it will start with the destination MAC and end
with the payload. It does not contain the preamble, SFD, padding, and CRC
fields.
*Peer list* (message type 1)::
This packet contains the peer list of the sender. The first byte after the
switch byte contains the number of IPv4 addresses that follow.
After that, the specified number of addresses follow, where each address
is encoded in 6 bytes. The first 4 bytes are the IPv4 address and the later
2 bytes are port number (both in network byte order).
After those addresses, the next byte contains the number of IPv6 addresses
that follow. After that, the specified number of addresses follow, where
each address is encoded in 18 bytes. The first 16 bytes are the IPv6 address
and the later 2 bytes are port number (both in network byte order).
*Initial message* (message type 2)::
This packet contains the following information:
 ** The stage of the initialization process
 ** A random node id to distinguish different nodes
 ** All the local subnets claimed by the nodes

+
Its first byte marks the stage of the initial handshake process.
The next 16 bytes contain the unique node id. After that,
the list of local subnets follows.
The subnet list is encoded in the following way: Its first byte of data
contains the number of encoded subnets that follow. After that, the given
number of encoded subnets follow.
For each subnet, the first byte is the length of bytes in the base address
and is followed by the given number of base address bytes and one additional
byte that is the prefix length of the subnet.
The addresses for the subnet will be encoded like they are encoded in their
native protocol (4 bytes for IPv4, 16 bytes for IPv6, and 6 bytes for a MAC
address) with the exception of MAC addresses in a VLan which will be encoded
in 8 bytes where the first 2 bytes are the VLan number in network byte order
and the later 6 bytes are the MAC address.
*Closing message* (message type 3)::
This packet does not contain any more data.

Nodes are expected to send an *initial message* with stage 0 whenever they
connect to a node they were not connected to before. As a reply to this message,
another initial should be sent with stage 1. Also a *peer list* message should
be sent as a reply.

When connected, nodes should periodically send their *peer list* to all
of their peers to spread this information and to avoid peer timeouts.
To avoid the cubic growth of management traffic, nodes should at a certain
network size start sending partial peer lists instead of the full list. A
reasonable number would be about 20 peers. The subsets should be selected
randomly.

Nodes should remove peers from their peer list after a certain period of
inactivity or when receiving a *closing message*. Before shutting down, nodes
should send the closing message to all of their peers in order to avoid
receiving further data until the timeout is reached.

Nodes should only add nodes to their peer list after receiving an initial
message from them instead of adding them right from the peer list of another
peer. This is necessary to avoid the case of a large network keeping dead nodes
alive.

== COPYRIGHT

Copyright (C) 2015-2020  Dennis Schwerdel
This software is licensed under GPL-3 or newer (see LICENSE.md)